The Riken Keiki GM-600 is an indoor stand-alone Ethylene Oxide monitor.
Ethylene Oxide is used for the Sterilization of hardware and is extremely toxic . Staff working in Sterilization facilities must have early warning of any leaks.
Using the GM-600 allows users to have advanced warning of any Ethylene Oxide leaks should they occur.
Users find the compact and lightweight GM-600 very easy to use and install in addition users can mount the monitors at staff eye level.
The GM-600 has a display that changes colour at each alarm level. This is a unique feature of the Riken Keiki 600 series of instruments.
The Unit comes with preset alarms set to High and High High. Users can program their own alarm levels if desired. Users can access relay outputs for 1st and 2nd alarms in addition to a 4-20mA output. These features allow customers to connect optional external accessories such as such as additional sounders and beacons.
The Instrument comes ready to operate with a 24 VDC Power supply. An optional 240VAC Main adapter is also available.
The GM-600 has a highly sensitive semiconductor sensor.
The GM-600 comes complete with a 3m extender cable allowing users to be mount the monitor outside the room with the sensor inside. This protects staff, allowing users to ascertain the state of the room prior to entry.
Customers of the GM-600 are those using Ethylene Oxide Sterilization autoclaves in addition to Research Laboratories.
The GM-600 is a high performance cost effective solution when Ethylene Oxide monitoring is required.
Standalone Indoor Ethylene Oxide monitor for detecting gas leakage from sterilization equipment.
|Detection Principle||Semiconductor Method|
|Gas Detected||Ethylene Oxide ( EO)|
|Sampling Method||Diffusion or remote sampling method with optional extender cable|
|Gas Alarm Contact||No-voltage contact 1a or 1b and normally de-energized ( energized in response to an alarm )|
|Fault alarm pattern||Auto-reset|
|Alarm Levels||Two preset alarms (H-HH), alarm 1 = 10ppm , alarm 2 = 50ppm|
|Display of Alarm||1st gas alarm: , flashing AL1 light or orange light, buzzer
2nd gas alarm: , flashing AL2 light or red light, buzzer
|Alarm Method||Latching or Non-latching|
|Alarm Contact||Dry contact, Form A or Form B, Form A standard Factory Setting, normally open (closed in ALARM)|
|Display||Digital LCD (5 digits, 7 segments / Green, Orange, Red) ( back light will be OFF during normal operation)|
|Trouble Alarm / Self-Diagnosis||System trouble / sensor connection trouble|
|Display of Trouble Alarm||Buzzer / content indication (flashing of orange error message)|
|Trouble Alarm Method||Non-latching or Latching|
|Contact Capacity||125VAC, 1A or 30VDC, 1A (Resistive load)|
|Output Signal||4 ~ 20mA (Non-isolated, Resistive load under 300O)|
|Remote Extender Cable||3M Extender cable with remote sensor head|
|Power Sources||24VDC±10%, ( 240VAC adapter available )|
|Power Consumption||24VDC specification: MAX 4W|
|Gas Alarm pattern||Auto-reset|
|Initial Clear||About 25 seconds|
|Operating Temperature||0°C ~ 40°C (no sudden change)|
|Operating Humidity||Below 90%RH (non-condensing)|
|Mounting Equipment||Wall mounting, sensor integrate type or remote type|
|Dimension||Body: approx. 80mm(W) x 120mm(H) x 35.5mm(D) / 3.15”(W) x 4.72”(H) x 1.2”(D)
Remote sensor (exclude the protrusion): approx. 40mm(W) x 96mm(H) x 35.5mm(D) / 1.57”(W) x 3.78”(H) x 1.2”(D)
|Weight||24VDC specification: approx. 180g (6.34 oz), Remote sensor: approx. 55g (1.94 oz) (excluding cable)|
|*Under normal conditions|